It brings HDMI signal with resolution up to 2048x2160 to any computer for video.Providing that your laptop supports USB-C charging then a portable charger for a laptop marked with PD (power delivery) which supplies at least 20Wh can be used to extend the battery life of the laptop. Many electronic components work together to provide smooth power to your laptop.USB Capture HDMI Gen 2 supports one HDMI input with embedded audio. Sjsz110/220 Conical Twin-Screw Lvt/PVC/WPC/Spc Flooring Production Line/Making Machine/Extrusion Line/Extruder.Inside the Macbook charger. 3 Color Doorligth, Sound, Light Alarm. Medicare Equipment, Wireless Calling System. Hospical Corridor Light, Nurse Call Lamp, Nurse Call Alarm.I was going to get a 150W can inverter from my local Jaycar but there were out of stock but the guy also said they have had issues with them failing when running laptop chargers.Switching power supplies are now very cheap, but this wasn't always the case.In the 1950s, switching power supplies were complex and expensive, used in aerospace and satellite applications that needed small, lightweight power supplies.By the early 1970s, new high-voltage transistors and other technology improvements made switching power supplies much cheaper and they became widelyThe introduction of a single-chip power supply controller in 1976 made switching power supplies simpler, smaller, and cheaper.Apple's involvement with switching power supplies goes back to 1977 when Apple's chief engineer Rod Holt designed a switching power supply for the Apple II."That switching power supply was as revolutionary as the Apple II logic board was. The Dell charger I believe is 90W while the Apple charger is 60W (my 15' MBP uses an 85W). Most consumer electronics, from your cell phone to your television, use a switching power supply to convert AC power from the wall to the low-voltage DC used by electronic circuits.Whenever you connect your password-protected drive to a computer that does not have the WD Security or WD Drive Utilities software installed, you can use the WD.A couple hours earlier I was using my laptop fine and once I was done using it I took off my charger out of my laptop and left I just got back on and plug back in my charger but it wouldn't fit, the charger would be stuck and unlike before where it was inserted smoothly my charger wouldn't budge into the jack I need help please.The switching power supply gets its name because it switches power on and off thousands of times a second, which turns out to be a very efficient way to do this conversion.
Do I Need To Use A Converter For My Laptop Charger In China Serial Number Next ToThe primary circuit is the heart of the charger.It takes the high voltage DC from the PFC circuit, chops it up and feeds it into the transformer to generate the charger's low-voltage output (16.5-18.5 volts).The charger uses an advanced design called a resonant controller, which lets the system operate at a very high frequency, up to 500 kilohertz.The higher frequency permits smaller components to be used for a more compact charger. Two of the largest components in the charger are the inductor and PFC capacitor that help boost the voltage to about 380 volts DC. If too many devices do this, it causes problems for the power company.Regulations require larger chargers to use a technique called power factor correction so they use power more evenly.The PFC circuit uses a power transistor to precisely chop up the input AC tens of thousands of times a second contrary to what you might expect, this makes the load on the AC line smoother. The diode bridge rectifier is attached to the metal heat sink with a clip.The next step in the charger's operation is the Power Factor Correction circuit (PFC), labeled in purple.One problem with simple chargers is they only draw power during a small part of the AC cycle. The picture below shows several features that can help distinguish the charger from counterfeits: the Apple logo in the case, the metal (not plastic) ground pin on the right, and the serial number next to the ground pin.The input components in a Macbook charger. Every computer now uses switching power supplies, and they all rip off Rod Holt's design."This is a fantastic quote, but unfortunately it is entirely false.The switching power supply revolution happened before Apple came along, Apple's design was similar to earlier power supplies And other computers don't use Rod Holt's design.Nevertheless, Apple has extensively used switching power supplies and pushes the limits of charger design with their compact, stylish and advanced chargers.For the teardown I started with a Macbook 85W power supply, model A1172, which is small enough to hold in your palm.The two sides are separated by a distance of about 6 mm, and only special components can cross this boundary.The transformer safely transmits power between the primary and the secondary by using magnetic fields instead of a direct electrical connection.The coils of wire inside the transformer are triple-insulated for safety.Cheap counterfeit chargers usually skimp on the insulation, posing a safety hazard.The optoisolator uses an internal beam of light to transmit a feedback signal between the secondary and primary. The filter capacitors smooth out the power, which leaves the charger through the output cable.The most important role of the secondary is to keep the dangerous high voltages in the rest of the charger away from the output, to avoid potentially fatal shocks.The isolation boundary marked in red on the earlier diagram indicates the separation between the high-voltage primary and the low-voltage secondary. The transformer and capacitor resonate at this frequency, smoothing the chopped-up input into a sine wave.The secondary: smooth, clean power outputThe secondary side of the circuit generates the output of the charger.The secondary receives power from the transformer and converts it DC with diodes. The chip in the middle controls the switching power supply circuit.The two drive transistors (in the overview diagram) alternately switch on and off to chop up the input voltage. The circuit board inside the Macbook charger.The PFC controller chip and the power supply (SMPS) controller chip are the main integrated circuits controlling the charger.The voltage reference chip is responsible for keeping the voltage stable even as the temperature changes. The charger's underside: many tiny componentsTurning the charger over reveals dozens of tiny components on the circuit board. The three-pin chip on the left (IC202) reduces the charger's 16.5 volts to the 3.3 volts required by the processor. The MPS430 processor monitors the charger's voltage and current.The square orange pads on the right are used to program software into the chip's flash memory during manufacturing. File sync programs for macThis allows the charger to be compatible with lower-voltage 60 watt chargers, while still providing 85 watts for laptops that can use it. For 85 watts, the voltage increases to 18.5 volts at 4.6 amps. One reason the charger has more control components than a typical charger is its variable output voltage.To produce 60 watts, the charger provides 16.5 volts at 3.6 amps. To the left of it, the current sense resistors measure the current flowing to the laptop.The printed circuit board from an Apple 85W Macbook power supply, showing the tiny components inside the charger.The isolation boundary (marked in red) separates the high voltage circuitry from the low voltage output components for safety.The dashed red line shows the isolation boundary that separates the low-voltage side (bottom right) from the high-voltage side.The optoisolators send control signals from the secondary side to the primary, shutting down the charger if there is a malfunction. ![]() Other laptop chargers simply provide 16 volts and when you plug it in, the computer uses the power. When the Magsafe connector is plugged into a Macbook, the laptopThe microcontroller in the charger detects this and after exactly one second enables the power output.The laptop then loads the charger information from the Magsafe connector chip.Starts pulling power from the charger and sends a command through the data pin to light the appropriate connector LED.When the Magsafe connector is unplugged from the laptop, the microcontroller detects the loss of current flow and shuts off the power, which also extinguishes the LEDs.You might wonder why the Apple charger has all this complexity. During this time, there are complex interactions between the Macbook, the charger, and the Magsafe connector.When the charger is disconnected from the laptop, the output transistor discussed earlier blocks the output power. Sold girl town patch downloadThe genuine charger has many more components.Flipping the chargers over and looking at the circuit boards shows the much more complex circuitry of the Apple charger.The imitation charger has just one control IC (in the upper left). From the outside, the charger looks just like an 85W Apple charger except it lacks the Apple name and logo.But looking inside reveals big differences.The photos below show the genuine Apple charger on the left and the imitation on the right.The circuit board of the Apple 85W Macbook charger (left) compared with an imitation charger (right). Do you get anything for the extra $65?I opened up an imitation Macbook charger to see how it compares with the genuine charger.
0 Comments
Leave a Reply. |
AuthorJason ArchivesCategories |